Eric Joe Salvador A. Romeroso

• Inspect EXT and QEC components in accordance with the approved technical manuals and procedures.
• Inspect the zone 1 fancase,EXT and QEC components, tubes and brackets in accordance with the approved technical manuals and procedures.
• Analysing and interpreting documentation such as service bulletin, SIL's, AD's, OEM and customer manuals.
• Processing of EXT, QEC components, tubes and brackets thru SAP.
• Used critical thinking to break down problems, evaluate solutions and make decisions for components and parts serviceability.
• Training and assisting cross trained and apprentices.

Worked on Engine Horizontal Build (Trent 1000, 1000-TEN, 900 and 7000)

• · Marrying of fan case and Engine core in vertical position
• · Installation of wing bib
• · Installation of upper and lower splitter
• · Installation of brackets, tubes and panel
• · Installation of radial drive shaft
• · Installation of LP shaft and set lock
• · Installation and routing of electrical harness
• . Fan fitment
• . Module 01 assembling and balancing

• Worked on aircraft type Air Bus 330 Trent 700, assigned on engine section.
• · Removal and installation of Fan Blade.
• · Elimination and installation of Integrated Drive Generator (IDG).
• · Removal and installation of Electric Magnetic Chip Detector (EMCD).
• · Removal and installation of Thrust Reverser.
• · Removal and installation of Fan Cowl.
• · Removal and installation of Spinner Cone.
• · Removal and installation of Air Intake Cowl.
• · Removal and installation of Common Nozzle Assembly.
• · Engine oil servicing.
• · Engine Filter Change.
• Worked on aircraft type Boeing 767-300 and -400, assigned on cargo section.
• · Removal and installation of equipment cooling duct.
• · Removal and installation of cargo handlings.
• · Removal and installation of waste and water tank.
• · Removal and installation of sidewalls, ceiling and floor panels.
• · Removal and installation of fire extinguisher bottle.
• · Removal and installation of cargo door liner.
• · Door lubrication.
• Worked on aircraft type Boeing 767-300 and -400, water and waste line modification.
• Worked on aircraft type Boeing 767-300 and -400, crew rest modification.
• · Carry out and accomplished modification based on drawings and task card given.
• ·
• Worked on aircraft type Boeing 767-300 and -400, assigned on cockpit section.
• · Removal and installation of windows and wiper.
• · Removal and installation of panels and seats.
• · Window lubrication.
• Worked on aircraft type Boeing 767-300 and -400, assigned on empennage section.
• · Removal and installation of access panels.
• · Performed Elevator and Rudder pre play check.
• · Removal installation of elevator PCU.
• · Hinge lubrication.
• Worked on aircraft type Boeing 747-400, assigned on cockpit section.
• · Removal and installation of panels and seats.
• Worked on aircraft type Boeing 747-400, assigned on cabin section.
• · Installation of seats
• · Removal and installation of passenger door slide raft.
• · Removal and installation of door liners.
• · Removal and installation of fire bottles.
• · Removal and installation of cargo handlings (freighter aircraft).
• · Removal and installation of sidewalls, ceiling and floor panels (freighter aircraft).
• · Pessenger door lubrication.
• Worked on aircraft type Boeing 747-400, assigned on cargo section.
• · Removal and installation door liners.
• · Removal and installation of side walls, ceiling and floor panels.
• · Cargo door lubrication.
• · Removal and installation of cargo handlings.
• ·
• Worked on aircraft type Boeing 747-400, assigned on landing gear section.
• · Removal and installation of wheel and brakes.
• · Performed gear servicing and lubrication.
• Worked on aircraft type Airbus 330-300, assigned on empennage section.
• · Removal and installation of vertical fin.
• · Removal and installation of access panels (horizontal stabilizer and rudder).
• · Hinges lubrications.
• · Removal and installation of Rudder.
• · Removal and installation of APU.
• · Removal and installation of rudder and elevator PCU.
• · Performed balls screw check.
• · Performed rudder and elevator pre play check.
• Worked on aircraft type Airbus 330-300, assigned on cabin section.
• · Removal and installation of passenger window.
• · Removal and installation of passenger door escape slide raft.
• · Removal and installation of door liners
• · Removal and installation of floor panels.
• · E-pass bottle servicing.
• Worked on aircraft type Airbus 330-300, assigned on landing gear section.
• · Removal and installation of wheels and brakes.
• · Removal and installation of boogie pin.
• · Main and forward gear servicing.
• · Gear Oil replenishment.
• Worked on aircraft type Boeing 777, assigned on cabin section.
• · Removal and installation of door liners.
• · Removal and installation of passenger door slide raft.
• · Removal and installation of floor panels.
• Worked on aircraft type Boeing 777, assigned on empennage section.
• · Removal and installation of elevator access panels.
• · Removal and Installation of Rudder assy.
• · Performed elevator PCU pre play check.
• · Elevator hinges lubrication.
• Worked on aircraft type Boeing 777 water and waste line modification.
• Worked on aircraft type Boeing 767-300 (BCF Program)
• Removed and replaced different parts and components with accordance’s to the AMM.

• Aircraft servicing
• Aircraft towing
• Aircraft lubrication
• Removal and installation of engine
• Removal and installation of pitch link
• Removal and installation of powertrain section of MG-520
• Removal and Installation of tail rotor blade of MG-520